So if you have been following my blog lately you may have noticed me rambling on about trying to get a Xbox 360 chat pad and an ps3 keypad working with a raspberry pi to make a portable terminal. I have finally finished my quest so join me below to see how I did it
The Atari 5200 is a vintage gaming system from the early 1980s. At the time I owned a 2600, but I always wanted a 5200. Well, in 2018 I finally decided to find one on eBay and buy it. I learned that the first thing you want to do after attaining a new gaming console is to get your hands on every available game cartridge for it, so I made this multi-ROM cartridge.
A multi-ROM cartridge, or “MultiCart” is a cartridge that contains more than one ROM image. There are multiple ways to go about this from selector switches to pick the cartridge you want, to built-in in game menu systems. I decided to go the route of using a Raspberry Pi for the user interface, making a WEB UI available to pick which cartridge is used.
The goal is not simply to play retro games on modern hardware — there’s any number of emulation solutions for that. The goal is to play retro games on retro hardware, but use a modern system to load the game image into the console.
This tutorial is inspired by dg0opk’s videos and blog post on monitoring QRP with single board computers. We’ll show you how to set up a super cheap QRP monitoring station using an RTL-SDR V3 and a Raspberry Pi 3. The total cost should be about US $56 ($21 for the RTL-SDR V3, and $35 for the Pi 3).
With this setup you’ll be able to continuously monitor multiple modes within the same band simultaneously (e.g. monitor 20 meter FT8, JT65+JT9 and WSPR all on one dongle at the same time). The method for creating multiple channels in Linux may also be useful for other applications. If you happen to have an upconverter or a better SDR to dedicate to monitoring such as an SDRplay or an Airspy HF+, then this can substitute for the RTL-SDR V3 as well.
If you spend a lot of time building things with a raspberry pi you will eventually run into the problem that you have booted your pi it’s not plugged into a tv/monitor and it’s not connected to wifi. You don’t want to just turn it off because it could corrupt the sd card so what do you do. I recently ran into this problem but luckily I had a serial adaptor on hand to hook up and tell my pi to turn off.
See the full post on his blog and the GitHub repository here.
The Raspberry Pi’s 40-pin GPIO connector often gets overlooked. Typical Pi projects use the hardware as a very small desktop PC (RetroPie, Pi-hole, media center, print server, etc), and don’t make any use of general-purpose IO pins. That’s too bad, because with a little bit of work, the Raspberry Pi can make a powerful physical computing device for many applications.
Couple of months back we decided to create our own media server to store our MP3s and digital photographs. But it gets postpone several months due to unavailability of main-boards and other resources. Finally, after reviewing several prototypes we decided to build our media server using Banana Pi (BPI) and MiniDLNA. Before finalize BPI we checked several main-boards which including Raspberry Pi B+, Orange Pi One and BeagleBone Black. Out of all above main-boards we choose BPI M1 because of its inbuilt SATA2.0 interface, Gigabit Ethernet port and availability in local market.
The 2 down sides to my ZeroBoy build I did recently were that it didn’t have a build in battery power and that it didn’t have sound. I seen that the MintyPi was using a USB sound card to give their handheld a speaker by soldering a speaker to the 3.5mm jack. So I thought I could do the same to add sound to my ZeroBoy.
A nice build log of ZeroBoy portable retropie project, that is available on Github:
You know when you see something and it give you instant inspiration and you also see a few ways you would also improve it. The thing I seen was wonky resistor score zero it’s basically a raspberry pi “hat” that has buttons in the layout of a nes controller. What I first thought was to make my own “hat” but flip it 180 degrees and add pass though pins so I could add a screen on top of that. Joint me below for my journey I went though.
I picked up a Roland SC-55 to use with my retrocomputer setup recently, and I figured it would be cool to turn the thing into a standalone midi jukebox, so that no “computer” is required. I also figured this would be relatively easy, using a raspberry pi as the controller to drive the SC-55. My first step was to figure out how to get MIDI out from a raspberry pi. One option would have been to purchase a USB-MIDI adapter. This would have worked, but I really wanted to develop a native raspberry pi MIDI interface rather than using USB. MIDI is a fairly simple interface, and the raspberry pi has built in serial capability, so this ought not to be too difficult.
Project details can be found on Dr. Scott M. Baker’s blog.